Makita Sander 9045B User Manual

Finishing Sander  
MODEL 9045B  
003269  
DOUBLE  
INSULATION  
I N S T R U C T I O N M A N U A L  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
 
5. Avoid body contact with grounded sur-  
faces such as pipes, radiators, ranges and  
refrigerators. There is an increased risk of  
electric shock if your body is grounded.  
14. Use safety equipment. Always wear eye  
protection. Dust mask, non-skid safety  
shoes, hard hat, or hearing protection must  
be used for appropriate conditions. Ordinary  
eye or sun glasses are NOT eye protection.  
6. Do not expose power tools to rain or wet  
conditions. Water entering a power tool will  
increase the risk of electric shock.  
Tool Use and Care  
15. Use clamps or other practical way to  
secure and support the workpiece to a  
stable platform. Holding the work by hand or  
against your body is unstable and may lead  
to loss of control.  
7. Do not abuse the cord. Never use the cord  
to carry the tools or pull the plug from an  
outlet. Keep cord away from heat, oil,  
sharp edges or moving parts. Replace  
damaged cords immediately. Damaged  
cords increase the risk of electric shock.  
16. Do not force tool. Use the correct tool for  
your application. The correct tool will do the  
job better and safer at the rate for which it is  
designed.  
8. When operating a power tool outside, use  
an outdoor extension cord marked “W-A”  
or “W”. These cords are rated for outdoor  
use and reduce the risk of electric shock.  
17. Do not use tool if switch does not turn it  
on or off. Any tool that cannot be controlled  
with the switch is dangerous and must be  
repaired.  
Personal Safety  
9. Stay alert, watch what you are doing and  
use common sense when operating a  
power tool. Do not use tool while tired or  
under the influence of drugs, alcohol, or  
medication. A moment of inattention while  
operating power tools may result in serious  
personal injury.  
18. Disconnect the plug from the power  
source before making any adjustments,  
changing accessories, or storing the tool.  
Such preventive safety measures reduce the  
risk of starting the tool accidentally.  
19. Store idle tools out of reach of children  
and other untrained persons. Tools are  
dangerous in the hands of untrained users.  
10. Dress properly. Do not wear loose cloth-  
ing or jewelry. Contain long hair. Keep  
your hair, clothing, and gloves away from  
moving parts. Loose clothes, jewelry, or  
long hair can be caught in moving parts.  
20. Maintain tools with care. Keep cutting  
tools sharp and clean. Properly maintained  
tools with sharp cutting edges are less likely  
to bind and are easier to control.  
11. Avoid accidental starting. Be sure switch  
is off before plugging in. Carrying tools with  
your finger on the switch or plugging in tools  
that have the switch on invites accidents.  
21. Check for misalignment or binding of  
moving parts, breakage of parts, and any  
other condition that may affect the tools  
operation. If damaged, have the tool ser-  
viced before using. Many accidents are  
caused by poorly maintained tools.  
12. Remove adjusting keys or wrenches  
before turning the tool on. A wrench or a  
key that is left attached to a rotating part of  
the tool may result in personal injury.  
22. Use only accessories that are recom-  
mended by the manufacturer for your  
model. Accessories that may be suitable for  
one tool, may become hazardous when used  
on another tool.  
13. Do not overreach. Keep proper footing  
and balance at all times. Proper footing and  
balance enables better control of the tool in  
unexpected situations.  
3
 
24. When servicing a tool, use only identical  
replacement parts. Follow instructions in  
the Maintenance section of this manual.  
Use of unauthorized parts or failure to follow  
Maintenance instructions may create a risk of  
electric shock or injury.  
SERVICE  
23. Tool service must be performed only by  
qualified repair personnel. Service or main-  
tenance performed by unqualified personnel  
could result in a risk of injury.  
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition.  
When using an extension cord, be sure to use one heavy enough to carry the current your  
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of  
power and overheating. Table 1 shows the correct size to use depending on cord length and  
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-  
ber, the heavier the cord.  
Table 1: Minimum gage for cord  
Volts  
120 V  
Total length of cord in feet  
Ampere Rating  
25 ft.  
50 ft.  
100 ft.  
150 ft.  
More Than  
Not More Than  
AWG  
0
6
10  
12  
6
18  
18  
16  
14  
16  
16  
16  
12  
16  
14  
14  
14  
12  
12  
10  
12  
16  
Not Recommended  
SPECIFIC SAFETY RULES  
USB040-4  
DO NOT let comfort or familiarity with product (gained from  
repeated use) replace strict adherence to sander safety rules. If  
you use this tool unsafely or incorrectly, you can suffer serious  
personal injury.  
1. Hold tool by insulated gripping surfaces  
when performing an operation where the  
cutting tool may contact hidden wiring or  
its own cord. Contact with a livewire  
will make exposed metal parts of the tool  
liveand shock the operator.  
4. Do not leave the tool running. Operate the  
tool only when hand-held.  
5. This tool has not been waterproofed, so  
do not use water on the workpiece sur-  
face.  
6. Ventilate your work area adequately when  
2. Always use safety glasses or goggles.  
Ordinary eye or sun glasses are NOT  
safety glasses.  
you perform sanding operations.  
7. Use of this tool to sand some products,  
paints and wood could expose user to  
dust containing hazardous substances.  
Use appropriate respiratory protection.  
3. Hold the tool firmly.  
4
 
SAVE THESE INSTRUCTIONS  
WARNING:  
MISUSE or failure to follow the safety rules stated in this  
instruction manual may cause serious personal injury.  
5
 
FUNCTIONAL  
DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before adjusting or checking function on the  
tool.  
003279  
Switch action  
CAUTION:  
1
Before plugging in the tool, always check to see that the  
tool is switched off.  
Switch can be locked in ONposition for ease of  
operator comfort during extended use. Apply caution  
when locking tool in ONposition and maintain firm  
grasp on tool.  
1. Slide switch  
To start the tool, slide the slide switch forward. To stop the  
tool, slide it backward.  
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before carrying out any work on the tool.  
003303  
Installing or removing abrasive paper  
1
2
3
To install the abrasive paper, pull back on the lever clip to  
open the paper clamp. Insert the paper end between the  
base and the paper clamp. Center the paper and align the  
edges parallel to the pad, then release the lever clip to  
secure the paper. (Prebending paper makes attachment  
easier.)  
4
1. Lever clip  
2. Paper clamp  
3. Abrasive paper  
4. Base  
Repeat the same process for the other end of the base,  
maintaining the proper paper tension.  
6
 
OPERATION  
003330  
Sanding operation  
CAUTION:  
Never run the tool without the abrasive paper. You may  
seriously damage the pad.  
Never force the tool. Excessive pressure may decrease  
the sanding efficiency, damage the abrasive paper or  
shorten tool life.  
Hold the tool firmly. Turn the tool on and wait until it attains  
full speed. Then gently place the tool on the workpiece sur-  
face. Keep the pad flush with the workpiece and apply slight  
pressure on the tool.  
MAINTENANCE  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before attempting to perform inspection or  
maintenance.  
001145  
Replacing carbon brushes  
Remove and check the carbon brushes regularly. Replace  
when they wear down to the limit mark. Keep the carbon  
brushes clean and free to slip in the holders. Both carbon  
brushes should be replaced at the same time. Use only iden-  
tical carbon brushes.  
1
1. Limit mark  
003345  
Use a screwdriver to remove the brush holder caps. Take out  
the worn carbon brushes, insert the new ones and secure  
the brush holder caps.  
1
2
To maintain product SAFETY and RELIABILITY, repairs, any  
other maintenance or adjustment should be performed by  
Makita Authorized or Factory Service Centers, always using  
Makita replacement parts.  
1. Brush holder cap  
2. Screwdriver  
7
 
ACCESSORIES  
CAUTION:  
These accessories or attachments are recommended for  
use with your Makita tool specified in this manual. The  
use of any other accessories or attachments might  
present a risk of injury to persons. Only use accessory or  
attachment for its stated purpose.  
If you need any assistance for more details regarding these  
accessories, ask your local Makita service center.  
Abrasive papers  
8
 
Stamp  
Timbre  
Makita Canada Inc.  
1950 Forbes Street,  
Whitby, Ontario  
L1N 7B7  
Fold  
 
Your answers to the following questions are appreciated.  
1.This product was purchased from?  
3. How did you first learn of Makita Power Tools?  
Hardware/lumber Store  
Tool Distributor  
Industrial Supply  
Other (  
Magazine/Newspaper  
From dealer  
Catalog  
Other (  
)
)
Store display  
2. Use of the product is intended for?  
4. Most favored points are?  
Construction trade  
Home maintenance  
Other (  
Design  
Makita Brand  
Power  
Industrial maintenance  
)
Features  
Size  
Other (  
)
Price  
5. Any comments?  
Certificate of Warranty  
Mail to Makita  
Date Purchased  
Model No.  
Serial No.  
Month  
Day  
Year 20  
Male Female  
Single  
Married  
Initial Last Name  
Street Address  
City  
Province  
Postal Code  
Under 19  
20-29  
30-39  
40-49  
Over 50  
AGE:  
Occupation:  
Dealer's Name & Address:  
 
Paste Paste Paste Paste Paste Paste  
Paste  
Paste  
Factory Service Centres  
Head Office:  
1950 Forbes St., Whitby, Ontario, L1N 7B7  
(905) 571 - 2200 1-800-263-3734  
Regional Office:  
11771 Hammersmith Way, Richmond  
B.C. V7A 5H6  
(604) 272 - 3104 1-800-663-0909  
Regional Office:  
(Montreal)  
6389 boul, Couture, St. Leonard, Quebec  
H1P 3J5  
(514) 323 - 1223 1-800-361-7049  
Dartmouth:  
202 Brownlow Avenue  
Dartmouth, N.S., B3B 1T5  
(902) 468 - 7064 1-888-625-4821  
Ville St. Laurent:  
(Montreal)  
1140 Rue Bégin, Ville St. Laurent, Quebec  
H4R 1X1  
(514) 745 - 5025 1-888-745-5025  
Les Saules:  
(Quebec)  
1200 St. Jean Baptiste, Unit 106, Les Saules,  
Quebec, G2E 5E8  
(418) 871 - 5720 1-800-663-5757  
Nepean:  
(Ottawa)  
203 Colonnade Road, Unit #6, Nepean,  
Ontario K2E 7K3  
(613) 224 - 5022 1-888-560-2214  
Whitby:  
1950 Forbes St., Whitby, Ontario, L1N 7B7  
(905) 571 - 2200 1-800-263-3734  
London:  
317 Adelaide St. S., Unit 117, London,  
Ontario, N5Z 3L3  
(519) 686 - 3115 1-800-571-0899  
Mississauga:  
Calgary:  
6350 Tomken Rd., Unit 8, Mississauga,  
Ontario, L5T 1Y3  
(905) 670 - 7255 1-800-221-9811  
#8-6115 Fourth St. S.E., Calgary  
Alberta, T2H 2H9  
(403) 243 - 3995 1-800-267-0445  
Edmonton:  
Richmond:  
Coquitlam:  
Winnipeg:  
Saskatoon:  
11614-149 Street, Edmonton, Alberta,  
T5M 3R3  
(780) 455 - 6644 1-888-455-6644  
11771 Hammersmith Way, Richmond, B.C.,  
V7A 5H6  
(604) 272 - 3104 1-800-663-0909  
2131 Hartley Ave., #103  
Coquitlam, B.C. V3K 2Z3  
(604) 525 - 7434 1-800-266-7738  
1670 St. James Street, Winnipeg, Manitoba,  
R3H 0L3  
(204) 694 - 0402 1-800-550-5073  
206A-2750 Faithful Avenue Saskatoon,  
Saskatchewan, S7K 6M6  
(306) 931 - 0111 1-888-931-0111  
For the authorized service centre nearest you please refer to the local yellow pages directory under toolsor con-  
tact our customer service department (Tel) 1-800-263-3734  
CUSTOMER RECORD  
When you need service...  
DATE  
Explain the problem in a letter  
PURCHASED:  
Enclose the letter with the tool  
DEALERS NAME  
Package carefully and send prepaid  
& ADDRESS:  
to the nearest Makita factory or  
authorized service centre  
MODEL NO.:  
SERIAL NO.:  
11  
 
MAKITA LIMITED ONE YEAR WARRANTY  
Warranty Policy  
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from  
workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during  
this one year period, return the COMPLETE tool, freight prepaid, to one of Makitas Factory or Authorized Service Centres.  
If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace)  
without charge.  
This Warranty does not apply:  
where normal maintenance is required,  
repairs have been made or attempted by others,  
the tool has been abused, misused or improperly maintained,  
alterations have been made to the tool.  
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM  
THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS  
WARRANTY.  
The Makita Warranty is the only and the entire written warranty given by Makita for the Makita tools. No dealer or his agent  
or employee is authorized to extend or enlarge upon this warranty by any verbal or written statement or advertisement.”  
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF  
MERCHANTABILITYAND FITNESS FOR A SPECIFIC PURPOSE,AFTER THE ONE YEAR TERM OF THIS WARRANTY.  
This Warranty gives you specific rights. The provisions contained in this warranty are not intended to limit, modify, take away  
from, disclaim or exclude any warranties set forth in any provincial legislation. To the extent required by law, the provisions in  
any provincial or federal legislation with respect to warranties take precedence over the provisions in this warranty.”  
Makita Corporation  
3-11-8, Sumiyoshi-cho,  
Anjo, Aichi 446-8502 Japan  
883256-236  
 

LaCie Computer Drive d2 Quadra User Manual
Lennox Hearth Indoor Fireplace Designer User Manual
LG Electronics Microwave Oven MD 2653GT User Manual
Makita Cordless Drill 6OLOSD User Manual
Marmitek Switch SWM1P User Manual
Masterbuilt Fire Pit MDCL User Manual
Memorex Cordless Telephone MPH2430 User Manual
Memorex MP3 Player MMP8570 User Manual
Microsoft Computer Accessories IC693CPU364 User Manual
Midland Radio Two Way Radio 75 440 User Manual