AMX TV Receiver CB TP7 User Manual

Installation Guide  
CB-TP7  
Rough-In Box for 7" Wall/Flush Mount Touch Panels  
1.  
Rest the right Stud Mounting tabs onto the stud (keeping the knockouts on the  
left). Be sure to leave enough of a gap between the stud and NXD Mounting tabs  
to accommodate the installation of the drywall or sheetrock after the rough-in  
box has been mounted. Ultimately, the Mounting Tabs should lie flush against  
the outside of the sheetrock.  
Overview  
The CB-TP7 Rough-In Box is an optional accessory for 7” Modero® Wall/Flush Mount  
Touch Panels. The Rough-In Box allows the panel to be mounted directly to the studs/  
pre-wall and includes a wall box and mounting screws.  
Wall Mount panels (NXDs) are contained within a metallic outer housing (back box).  
This back box is not removed when installing the NXD into a Rough-In Box. The back  
box is only removed to gain access for the replacement of the Compact Flash  
component or upgrade to the VESA housing.  
2.  
Fasten the CB-TP7 rough-in box to the stud through the holes on the right Stud  
Mounting tabs (FIG. 1), using either nails or screws.  
See reverse for  
detailed dimensions  
Specifications  
Stud  
CB-TP7 (FG035-10) Specifications  
Dimensions (HWD) • 5 1/2" x 7 1/4" x 3 3/8"  
• 13.9 cm x 18.4 cm x 8.6 cm  
Rough-In Box  
Do Not Use these  
tabs to mount  
the Rough-In Box  
Included  
Accessories  
• 4 Phillips pan-head (#4-40 x 0.375 Black) screws (80-0115)  
• 4 Phillips pan-head (#4-40 x 0.625 Black) screws (80-0118)  
Certifications  
• cTUVus Listed  
Rough-In Box  
must be installed  
with knockouts on  
this side  
WARNING: INSTALLER, LEAVE A GAP BETWEEN THE STUD AND ROUGH-IN  
BOX TO ACCOMMODATE THE DRYWALL/SHEETROCK.  
This gap allows the installation of the drywall/sheetrock after the CB-TP7 has been  
mounted onto the beams. The rough-in box installation must be done prior to any wall  
installation.  
Note: The most important thing to remember when mounting this rough-in box is that  
the mounting tabs must be mounted flush against the outside of the sheetrock.  
It is recommended that you cut out the surface slightly smaller than what is outlined in  
the installation drawings so that you can make any necessary cutout adjustments.  
The wiring knockouts on the left side will be used for the NXD-CV7 Wall Mount panel  
connectors, so always secure the rough-in box to the stud using the Stud Mounting  
Holes on the right side of the box.  
Front surface of  
mounting tabs should  
be flush with outside  
face of drywall  
Drywall  
FIG. 1 CB-TP7 - Drywall Installation  
Pre-Wall Installation of the CP-TP7 Rough-In Box  
Refer to the SP225802 diagram for detailed installation dimensions (see  
reverse).  
Cutting out the surface slightly smaller than what is outlined in the installation  
drawings, in order to make any necessary cutout adjustments, is highly  
recommended.  
The wiring knockouts on the left side will be used for the NXD-CV7 Wall Mount  
panel connectors, so always secure the rough-in box to the stud using the Stud  
Mounting Holes on the right side of the box.  
3.  
Remove the wiring knockouts from the left side of the CB-TP7 to accommodate  
the cables being threaded through to the NXD touch panel.  
Note: Remember that when mounting this rough-in box, the NXD mounting tabs must  
lie flush against the outside of the sheetrock.  
4.  
Thread the incoming power, RJ-45 audio/video, Ethernet, and USB wiring  
through the knockouts (use of the left wiring knockouts are recommended with  
this installation). Leave enough slack in the wiring to accommodate any re-  
positioning of the panel.  
5.  
Install the drywall/sheetrock before inserting the main NXD unit into the CB-TP7.  
Recommended Cutout for  
CB-TP7 Rough-In Box  
 
 

3M Microscope Magnifier 900AST User Manual
Advantech Computer Hardware RMD 1150 User Manual
AllerAir Air Cleaner A8PK7025 User Manual
Altec Lansing MP3 Docking Station IMV712 User Manual
Amana Dishwasher W10212195A User Manual
American Audio DJ Equipment Q D5 User Manual
American Standard Indoor Furnishings T555430 User Manual
Atlona Pacemaker AT HDTX User Manual
Ayre Acoustics Stereo Amplifier K 5XEMP User Manual
BC Speakers Speaker DE610 User Manual